8532 Low-cost compression load cell with IN-LINE amplifier

Relative non-linearity ≤ ±1.0 % F.S., normalized output signal 0 ... 10 V, stainless steel sensor, compact design, customer-specific versions possible from 20 pieces up

Product Inquiry

    Product comparison

      • Features

        • Measuring ranges between 0 ... 500 N and 0 ... 20 kN
        • Relative non-linearity: ≤ ±1.0 % F.S.
        • Normalized output signal 0 ... 10 V
        • Stainless steel sensor
        • Compact design
        • Customer-specific versions possible from 20 pieces up
        • burster TEDS optionally available
      • Product data

        Model 8532
        Measuring range

        0 … 500 N
        0 … 1 kN
        0 … 2 kN
        0 … 5 kN
        0 … 10 kN
        0 … 20 kN

        Direction of force Compression
        Standardization No
        Signal output 2 mV/V
        Protection class IP60
        Overload protection No
        Pull-plate No
        Load introduction button Yes
        Range of operating temperature -20 ... +80 °C
        Specific characteristics

        • Stainless steel sensor
        • Compact design
        • burster TEDS optionally available
      • Description

        This force measurement chain was developed for applications where a low cost solution is more important than achieving high levels of accuracy. The sensors strain gauge technology allows the measurement of static and dynamic forces. The load cell is also designed for applications that provide only little space due to its compact design. These properties, together with the sensors dust protection, make the measuring chain suitable for a wide range of applications, such as

        • Industrial manufacture
        • Manufacture of customized machinery
        • Geological investigations
        • Motor vehicle engineering
        • Commercial agriculture
        • Bridge building

        The body of the sensor is a flat, cylindrical disk, into which a domed force application knob is integrated. It is important that the force is applied axially to the center of the sensor. The domed form, however, minimizes the effect of a force that is not exactly axial.

        A full-bridge strain gauge is used as the measuring element inside the sensor, by means of which the force to be measured is converted into a proportional electrical voltage.

        The in-line amplifier increases this voltage from 0 up to 10 V. The surface against which the sensor rests is important for the quality of the measurement. It should be ground. It must be sufficiently hard and thick and not deform under load

      • Data Sheet & Downloads

        Data sheet
        Brochure
        Further info
      • Videos

        Please accept marketing-cookies to watch this video.

        Example showing load cell fitted under pre-load with extreme overload protection


        Youtube channel Burster Youtube Channel

      • Application Examples

        Checking the tension

        of a conveyor belt

      Related products




      burster in USA

      burster Inc.
      Adam Giorgione, Christina Giorgione: +1-706-331-0537; Darren McCulley: +1-440-214-5333
      adam.giorgioneburster.us; christina.giorgioneburster.us; darren.mcculleyburster.us; salesburster.us
      www.burster.us

      Product category :

      • Torque Sensors
      • Load Cells
      • Displacement Sensors
      • Mechanical and Electrical Calibration Solutions

      Company-Information Company-Information

      Physicom Corp.
      +1 4167543168
      salesphysicomcorp.com
      www.physicomcorp.com

      Product category :

      • Press-Fit Control / DIGIFORCE®
      • Process Instruments

      Company-Information Company-Information

      USA

      burster Inc.

      Adam Giorgione; Christina Giorgione
      105 Laurel Creek Rd. SE
      Suite: 10C Calhoun, GA. 30701

      Darren McCulley
      304 State Route 303
      44241 Streetsboro OH

      USA

      Fon: Adam Giorgione, Christina Giorgione: +1-706-331-0537; Darren McCulley: +1-440-214-5333
      adam.giorgioneburster.us; christina.giorgioneburster.us; darren.mcculleyburster.us; salesburster.us
      www.burster.us

      Product category :

      • Torque Sensors
      • Load Cells
      • Displacement Sensors
      • Mechanical and Electrical Calibration Solutions

      Physicom Corp.

      P.O. Box 462
      Scarborough, ON
      M1E 4Y9
      Kanada

      Fon: +1 4167543168
      Fax: +1 4167542351
      salesphysicomcorp.com
      www.physicomcorp.com

      Local sales support through different rep networks available, please inquire at Physicom.

      SERVICES

      • Qualified design, application support
      • Process optimization & rental equipment
      • Qualified commissioning, integration support & training
      • On-site trouble shooting & update service
      • Qualified phone & online support
      • Full repair facilities
      • Local calibration service

      Product category :

      • Press-Fit Control / DIGIFORCE®
      • Process Instruments
      ×
      © 2024 // burster präzisionsmesstechnik gmbh & co kg
      nach oben