8511 Bending beam tension and compression load cell

Highly accurate, very low mounting height, simple force introduction, for tension and compression, for static and dynamic measurement, material aluminium resp. stainless steel, protection class IP 54

Product Inquiry

    Product comparison

      • Features

        • For tension and compression forces
        • Measuring ranges from 0 ... 5 N to 0 ... 2 kN
        • Relative non-linearity: ≤ ±0.1 % F.S.
        • Very low mounting height
        • Simple force application
        • Material aluminium or stainless steel
        • Special design on request
        • burster TEDS optionally available
      • Product data

        Model 8511
        Measuring range

        0 … 5 N
        0 … 10 N
        0 … 20 N
        0 … 50 N
        0 … 100 N
        0 … 200 N
        0 … 500 N
        0 … 1000 N
        0 … 2000 N

        Direction of force Tension and compression
        Standardization Option
        Signal output

        1 mV/V
        1.5 mV/V
        depending on measuring range

        Protection class IP54
        Overload protection Option
        Range of operating temperature -30 ... +90 °C
        Specific characteristics

        • High linearity up to 0.1 %
        • Very low mounting height
        • Simple force application
        • Material aluminium or stainless steel
        • Special design on request
        • burster TEDS optionally available
      • Description

        The measuring element of the load cell consists of a double bending beam on which strain gages are applied. The applied force detunes the measuring bridge so that a proportional output voltage is generated. The strain gages on the measuring element are protected against dirt and water spray by a rubber bellows.

        The sensor can be easily mounted via two mounting holes. The tension or compression force to be measured is introduced at the opposite end perpendicular to the sensor axis.

        Due to its special design, the influence by an extension (e.g. touch finger) on the measuring signal is low. Overload protection can be realized with little effort using a mechanical stop.

      • Data Sheet & Downloads

        Data sheet
        Brochure
        Operation manual
        Further info
      • Videos

        Please accept marketing-cookies to watch this video.

        Example showing tightly-packed assembly of bending-beam load cells with overload protection


        Youtube channel Burster Youtube Channel

      • Application Examples

        Displacement measurement: real-time monitoring

        in the plastics industry

        Force measurement

        in tablet hardness-testing equipment

        Fx/Fy force measurement

        on the gear stick

        Measuring the internal tool pressure

        pressure transducer

        Measuring the supporting force in utility vehicles

        Ring load cell

        Tension measurement

        in paper manufacture processes

        Testing micro-switches

        during continuous mass production

      Related products




      burster in USA

      burster Inc.
      Adam Giorgione, Christina Giorgione: +1-706-331-0537; Darren McCulley: +1-440-214-5333
      adam.giorgioneburster.us; christina.giorgioneburster.us; darren.mcculleyburster.us; salesburster.us
      www.burster.us

      Product category :

      • Torque Sensors
      • Load Cells
      • Displacement Sensors
      • Mechanical and Electrical Calibration Solutions

      Company-Information Company-Information

      Physicom Corp.
      +1 4167543168
      salesphysicomcorp.com
      www.physicomcorp.com

      Product category :

      • Press-Fit Control / DIGIFORCE®
      • Process Instruments

      Company-Information Company-Information

      USA

      burster Inc.

      Adam Giorgione; Christina Giorgione
      105 Laurel Creek Rd. SE
      Suite: 10C Calhoun, GA. 30701

      Darren McCulley
      304 State Route 303
      44241 Streetsboro OH

      USA

      Fon: Adam Giorgione, Christina Giorgione: +1-706-331-0537; Darren McCulley: +1-440-214-5333
      adam.giorgioneburster.us; christina.giorgioneburster.us; darren.mcculleyburster.us; salesburster.us
      www.burster.us

      Product category :

      • Torque Sensors
      • Load Cells
      • Displacement Sensors
      • Mechanical and Electrical Calibration Solutions

      Physicom Corp.

      P.O. Box 462
      Scarborough, ON
      M1E 4Y9
      Kanada

      Fon: +1 4167543168
      Fax: +1 4167542351
      salesphysicomcorp.com
      www.physicomcorp.com

      Local sales support through different rep networks available, please inquire at Physicom.

      SERVICES

      • Qualified design, application support
      • Process optimization & rental equipment
      • Qualified commissioning, integration support & training
      • On-site trouble shooting & update service
      • Qualified phone & online support
      • Full repair facilities
      • Local calibration service

      Product category :

      • Press-Fit Control / DIGIFORCE®
      • Process Instruments
      ×
      © 2024 // burster präzisionsmesstechnik gmbh & co kg
      nach oben