8511 Load bending beam

Highly accurate, very low mounting height, simple force introduction, for tension and compression, for static and dynamic measurement, material aluminium resp. stainless steel, protection class IP 64

  • Features

    • For tension and compression forces
    • Measuring ranges from 0 ... 5 N to 0 ... 2 kN
    • Relative non-linearity: ≤ ±0.1 % F.S.
    • Very low mounting height
    • Simple force application
    • Material aluminium or stainless steel
    • Special design on request
    • burster TEDS optionally available
  • Product data

    Model 8511
    Measuring range

    0 … 5 N
    0 … 10 N
    0 … 20 N
    0 … 50 N
    0 … 100 N
    0 … 200 N
    0 … 500 N
    0 … 1000 N
    0 … 2000 N

    Direction of force Tension and compression
    Standardization Option
    Signal output

    1 mV/V
    1.5 mV/V
    depending on measuring range

    Protection class IP54
    Overload protection Option
    Range of operating temperature -30 ... +90 °C
    Specific characteristics

    • High linearity up to 0.1 %
    • Very low mounting height
    • Simple force application
    • Material aluminium or stainless steel
    • Special design on request
    • burster TEDS optionally available
  • Description

    Model 8511 bending beam load cells are designed for measuring tension and compression forces. Their high accuracy, low torque sensitivity and very low mounting height make these sensors particularly suitable for use in weighing and dosing technology as well as for laboratory and production use.

    Extremely simple force application makes the sensor easy to handle. It offers a very favorable price/performance ratio and can be used universally for static and dynamic measurements.

    Examples of application:

    • Dosing system
    • Load deflection curve
    • Tension force measurement for wire or thread winders
    • Friction forces
    • Cable force
    • Withdrawal force, etc

    The measuring element of this load cell consists of a double bending beam with strain gauges, the resistance of which changes with the application of force. Upon applying a voltage to the strain gauge bridge, the change in the strain gauge resistance is converted into output voltage, which is directly proportional to the force. The strain gauges and the entire measuring element are protected from water spray by rubber bellows.

    To install the load cell, it is securely clamped on the side with 2 bore holes. The tension or compression force to be measured is applied at the other end. Force is applied easily perpendicular to the sensor axis. This serves to prevent falsification of the measured values. The influence on the measuring signal resulting from the increase of load distance on the mounting side (e.g. by a touch finger) is negligible. Overload protection can be realized with little effort using a mechanical stop.

  • Data Sheet & Downloads

    Data sheet
    Brochure
    Operation manual
    Further info
  • Videos

    Example showing tightly-packed assembly of bending-beam load cells with overload protection


    Youtube channel Burster Youtube Channel




burster in Canada

Physicom Corp.
+1 4167543168
salesphysicomcorp.com
www.physicomcorp.com

Product category :

  • Press-Fit Control / DIGIFORCE®
  • Process Instruments

Company-Information Company-Information

Canada

A-Tech Instruments Ltd.

Toronto Office
Physicom Corp.
P.O. Box 252
Scarborough, ON
M1E 4R5
Canada

Fon: +1 4167547008
Fax: +1 4167542351
salesa-tech.ca
www.a-tech.ca

Montreal Office
P.O. Box 447
Pointe Claire, PQ
H9R 4N9
KANADA

Fon: +1 5146955147
Fax: +1 5146306136

SERVICES

  • Qualified design, application support
  • Process optimization & rental equipment
  • Qualified commissioning, integration support & training
  • On-site trouble shooting & update service
  • Qualified phone & online support
  • Full repair facilities
  • Local calibration service

Physicom Corp.

P.O. Box 462
Scarborough, ON
M1E 4Y9
Canada

Fon: +1 4167543168
Fax: +1 4167542351
salesphysicomcorp.com
www.physicomcorp.com

Local sales support through different rep networks available, please inquire at Physicom.

SERVICES

  • Qualified design, application support
  • Process optimization & rental equipment
  • Qualified commissioning, integration support & training
  • On-site trouble shooting & update service
  • Qualified phone & online support
  • Full repair facilities
  • Local calibration service

Product category :

  • Press-Fit Control / DIGIFORCE®
  • Process Instruments
×

Solutions

Lösungen Bild

Sectors

Aerospace Industry
Automotive
Biotechnology
Chemical Industry
Food Industry
Machine Manufacturers
Medical Technology
Metal / Steel Industry
Others
Plastics Industry
Precision Engineering
Tool / Mold Construction
Utility Vehicles

Product Inquiry

    Product comparison

      Brandnew brochure: Load cells

      Discover our new brochure Load cells for production, automation, R&D and quality assurance with many application examples and product focused information!

      Download our new brochure

      © 2020 // burster präzisionsmesstechnik gmbh & co kg
      nach